Medical tubing material comparisons rarely produce one correct answer. The appropriate polymer depends on how the finished device is sterilized, what fluids move through the lumen, whether the tube runs in a peristaltic pump, and how the assembly is joined. Silicone remains the reference point for repeated steam processing and elastic recovery, while thermoplastic elastomers have lower permeability and weldable joints in many single-use circuits [2][3]. PVC persists in cost-sensitive applications but carries documented drug-compatibility limits [6]. Multilayer coextrusion lets designers combine an inner lubricious layer with an outer bondable layer, but processing temperature, flow characteristics and melt viscosity constrain which resins can share a die [6]. The evaluation should therefore begin with the sterilization and fluid-contact requirements, then narrow candidates by mechanical and assembly behavior.

Sterilization Regime as the First Filter

Steam autoclaving separates materials quickly. Saint-Gobain states that steam usually favors silicone unless a high-temperature thermoplastic is selected and cycle count is limited [2]. Eldon James lists several Flexelene TPE grades as autoclavable to 121°C, including the 135C series rated from -80°C to 135°C [1]. Cole-Parmer similarly reports autoclave compatibility for platinum-cured silicone, TPE, TPV and reinforced TPE formulations, while its PVC lab and vacuum tubing listing shows autoclave compatibility and its PVC fuel and lubricant tubing listing shows no sterilization method [3]. The distinction is not simply whether a material survives one cycle; repeated steam exposure can flatten softer thermoplastic variants even when initial flow performance is acceptable [2].

Radiation and ethylene oxide introduce different failure modes. Saint-Gobain cautions that radiation can yellow silicone while retaining function, and can stiffen or embrittle some thermoplastics, so validation should occur at end-of-life dose on finished assemblies [2]. Nordson MEDICAL states that its LLDPE tubing can be sterilized by gamma or EtO but autoclaving is not recommended, and that its polyurethane tubing should not be autoclaved because it may alter the chemical nature of the resin [4]. A device intended for gamma sterilization therefore cannot assume that a steam-rated silicone or TPE will behave identically under irradiation. The sterilization method should be fixed before comparing datasheet temperature ranges.

Permeability, Extractables and Fluid Contact

Gas and oxygen permeability differ materially between silicone and thermoplastic families. Saint-Gobain notes that many thermoplastic grades pass less gas than silicone, and that solvent options can hold dimensions and barrier under alcohols, lipids or aggressive cleaners [2]. Eldon James lists low gas and oxygen permeability for its Flexelene POE and TPE lines, with several grades tested to ISO 10993-4, ISO 10993-5 and USP 661 [1]. Nordson MEDICAL states that its biopharmaceutical-grade TPE has low absorption and permeability compared with silicone tubing [4]. These vendor claims describe relative barrier behavior, not absolute transmission rates, and should be confirmed against the specific drug or gas in the application.

Extractables and leachables testing appears across the source documents, but the test scopes are not uniform. Eldon James lists BPOG testing for certain Flexelene grades and USP 661 for multiple TPE products [1]. Cole-Parmer reports USP Class VI and USP <661> compliance for its TPE tubing, and USP Class VI plus FDA 21 CFR 177.2600 for platinum-cured silicone [3]. DuPont lists low extractables and good chemical resistance for its Liveo Pharma TPE tubing [5]. These listings establish that a material has been tested under stated protocols; they do not by themselves demonstrate suitability for a novel drug formulation. PVC introduces a separate risk: Nordson MEDICAL documents that insulin, nitroglycerine and oncology drugs such as paclitaxel can absorb into PVC tubing, resulting in a loss of potency, while the infusion solution can dissolve the plasticizer and other additives contained within the PVC [6].

Building a Comparison Matrix from Documented Properties

Start with four columns: sterilization method, fluid contact, mechanical duty and assembly. For each candidate, record only properties that appear in a supplier document or test listing. Eldon James publishes a comparison table with temperature range, Shore A hardness, barrier, flexibility, pump durability and chemical resistance ratings on a 1-to-10 scale, with autoclave notation for specific grades [1]. Cole-Parmer provides a formulation table covering acids, alkalies, organic solvents, hydrocarbons and oils, temperature range, compliance, sterilization and durometer [3]. Use these tables to eliminate candidates that fail a hard requirement, such as autoclave compatibility or a stated chemical resistance grade, before requesting application-specific test data. Do not treat a vendor's 1-to-10 rating as a substitute for your own worst-case validation.

Mechanical Behavior in Pumps and Tight Routing

Peristaltic pump duty stresses elastic recovery and fatigue life. Saint-Gobain identifies silicone's elastic recovery and kink resistance as strengths in clamp compression and bend recovery, while noting that softer thermoplastic grades can kink at tight radii unless wall thickness, braiding or routing changes [2]. Cole-Parmer describes its platinum-cured silicone as having low hysteresis and long service life in peristaltic pumps, and its TPV pharma grade as having chemical and kink resistance for pump performance [3]. DuPont lists a low-hysteresis silicone technology for extended peristaltic pump performance and filling accuracy [5]. These claims are vendor-specific and do not establish a universal ranking across all pump heads or tubing sizes.

Hardness and temperature range shape handling. Eldon James publishes Shore A values from 54 to 92 across its Flexelene TPE grades, with the MFX82M and MFX92R alloys rated from -57°C to 121°C [1]. Nordson MEDICAL lists 50 Shore A platinum-cured silicone, 80 durometer polyurethane and 65 Shore A TPE, with the polyurethane described as extremely kink resistant and resistant to abrasion [4]. Cole-Parmer reports a 60D durometer for PTFE tubing and 55A for PVC lab and vacuum tubing [3]. A softer durometer may improve patient comfort in wearables but can complicate pushability in long supported runs, a trade-off Saint-Gobain frames as a formulation decision rather than a fixed material property [2].

Assembly Economics and Multilayer Construction

Joining method changes the cost and reliability picture. Saint-Gobain lists solvent bonding, thermal or RF welding, and overmolding as thermoplastic advantages that reduce fittings and speed takt time [2]. The source does not state a corresponding silicone limitation for those joining methods. Nordson MEDICAL describes its TPE tubing as sterile weldable, heat sealable and moldable for single-use sampling, filling and storage tubing set assemblies [4]. DuPont lists its Liveo Pharma TPE tubing for aseptic connection and disconnection without connectors, citing improved heat-welding and high tensile strength and burst resistance before and after welding [5]. These assembly advantages apply to specific thermoplastic formulations, not to every TPE grade, and must be verified on the actual wall thickness and durometer selected.

Coextruded multilayer tubing allows a single shaft to combine properties that no monolayer material offers. Nordson MEDICAL explains that polyamide, TPE, polyurethane, PVC and polyolefins can be coextruded, but processing temperature, flow characteristics and melt viscosity constrain pairings; PEEK at roughly 660°F cannot be coextruded with polyethylene, which has a melt temperature of approximately 260°F [6]. The same source describes using lubricious inner-layer materials compatible with outer-layer materials, eliminating a tie layer and letting the middle layer change mechanical functionality [6]. A documented example pairs HDPE lubricity with Pebax bondability in a coronary implant delivery system [6]. Multilayer construction addresses trade-offs between lubricity, pushability and bonding, but it adds extrusion complexity and requires layer-ratio control that older equipment may not achieve [6].

A Structured Evaluation Example

Consider a hypothetical reusable surgical suction line that must withstand steam cycles several times per day. Saint-Gobain reports that a silicone version stayed dimensionally stable under this regime, while a soft TPE variant met flow on day one but flattened after repeated cycles [2]. This example does not prove silicone is always correct; it shows that the sterilization and cycle-count requirement should be tested before other properties are compared. An engineer would first confirm the steam recipe, then request dimensional and flow data after the full cycle plan for any thermoplastic candidate [2].

For a single-use bioprocess sampling assembly, the decision shifts toward weldability and barrier. DuPont lists TPE tubing for aseptic connection and disconnection without connectors and lists low extractables as a benefit [5]. Nordson MEDICAL similarly emphasizes sterile welding and heat sealing for TPE in single-use processes [4]. A comparison would then weigh burst pressure after welding, extractables under the process fluid, and pump life if the assembly includes a peristaltic segment. The same material that fails repeated steam may be the better choice for a gamma-sterilized disposable, which is why the evaluation must be tied to the actual use case rather than a generic material ranking.